• AR-15/M16 30RD SS MAGAZINE SPRING BROWNELLS More Detail

    AR-15/M16 30RD SS MAGAZINE SPRING BROWNELLS

    $2.99 - $19.99$2.99 - $19.99

    Bring Magazines Back To Top Performance Replacement springs install easily to eliminate problems caused by worn-out parts. Chrome silicon spring maintains proper tension and gives consistent feeding, also available with stainless steel spring. AR-15, Issue:11, Page:062 Big Book Catalog, Issue:69, Page:063

    HOT!
  • AR-15/M16 USGI ENHANCED SELF-LEVELING FOLLOWER MAGPUL More Detail

    AR-15/M16 USGI ENHANCED SELF-LEVELING FOLLOWER MAGPUL

    $5.65$5.65

    Won't Tilt; Feeds Rounds Smoothly; Helps Prevent Magazine-Related Failures Drop-in replacement follower for USGI 30-round magazines won’t tilt, so it helps prevent jams, misfeeds, and other magazine-related failures. Rectangular extensions at the front and rear prevent tilt of the round stack to eliminate jams caused by over-compression and binding of the spring. Self-lubricating polymer composition helps ensure smooth movement for easier loading and ultra-smooth feeding. Extended bolt catch makes sure bolt locks open after the last round is fired. A spring stabilizer molded into the underside keeps spring force centered no matter how many rounds are in the mag, rounded edges on the extensions for even slicker movement in the mag body, and more streamlined ramp geometry for easier travel of the round from the magazine into the chamber. AR-15, Issue:11, Page:062 Big Book Catalog, Issue:69, Page:063

    HOT!
  • AR-15/M16 USGI 30RD MAGAZINE FLOOR PLATE BROWNELLS More Detail

    AR-15/M16 USGI 30RD MAGAZINE FLOOR PLATE BROWNELLS

    $1.79 - $11.99$1.79 - $11.99

    Bring Magazines Back To Top PerformanceReplacement floorplates install easily to eliminate problems caused by worn-out parts. Anodized aluminum floorplate. AR-15, Issue:11, Page:062 Big Book Catalog, Issue:69, Page:063

    HOT!
  • AR-15/16 PMAG RANGER® FLOORPLATE 3 PACK MAGPUL More Detail

    AR-15/16 PMAG RANGER® FLOORPLATE 3 PACK MAGPUL

    $14.20 - $18.95$14.20 - $18.95

    Fast, Easy Mag Changes In High Stress Situations Replacement floorplate brings the speed and controllability of the original Magpul Ranger Floorplate to both 20- and 30-round PMAGs for fast, secure tactical magazine changes. Smoothly contoured, easy-to-grasp finger loop and grooved thumb dimple aid in positive extraction from tight mag pouches and help you hang onto the empty magazine with just a finger after a tactical reload. Made from tough, reinforced polymer overmolded with soft, non-slip synthetic rubber that also cushions the magazine from impact if dropped on a hard surface. Includes molded-in para-cord hole for custom loop configurations. Easy, drop-in installation: remove the PMAG’s factory floorplate as you do for cleaning, and replace it with the Ranger Floorplate. Sold in 3-paks and available in Black, Dark Earth, and  O.D. Green. AR-15, Issue:11, Page:060 AR-15, Issue:11, Page:061 Big Book Catalog, Issue:69, Page:060 Big Book Catalog, Issue:69, Page:061

    HOT!
  • AR-15/M16 30RD CS MAGAZINE SPRING BROWNELLS More Detail

    AR-15/M16 30RD CS MAGAZINE SPRING BROWNELLS

    $2.99 - $19.99$2.99 - $19.99

    Replacement springs install easily to eliminate problems caused by worn-out parts. Chrome silicon spring maintains proper tension and gives consistent feeding, also available with stainless steel spring. AR-15, Issue:11, Page:062 Big Book Catalog, Issue:69, Page:063

    HOT!
  • 9MM AR-15 32 ROUND MAGAZINE 3 PACK & LOADER BROWNELLS More Detail

    9MM AR-15 32 ROUND MAGAZINE 3 PACK & LOADER BROWNELLS

    $98.99$98.99

    Rugged heat treated steel magazine body Durable steel follower Matte black Xylan coated magazine body Xylan coating drastically reduces friction and provides excellent corrosion resistance Bolt hold open tab Easy to remove floorplate allows for quick maintenance and cleaning Round count indicator windows allow for a quick assessment of remaining ammunition Fits AR15 rifles that accept Colt style magazines Pocket-sized loaders allow fast and easy reloading of magazine clips ML-2 submachine gun magazine loader fits Beretta, Colt, H&K, Uzi 9mm Carbine, and submachine gun magazines Big Book Catalog, Issue:69, Page:062

    HOT!
  • AR-15/M16 PMAG MOE M2 DUST COVERS MAGPUL More Detail

    AR-15/M16 PMAG MOE M2 DUST COVERS MAGPUL

    $3.75$3.75

    Dependable & Nearly Indestructible Replacement Dust/Impact Covers available in Black, Dark Earth. These covers fit the Gen 2 mags, MAG570 and MAG571. Sold in 3-Paks. AR-15, Issue:11, Page:060 Big Book Catalog, Issue:69, Page:060

    HOT!
  • AR-15/M16 USGI MAGPUL FOLLOWER + SS SPRING KITS BROWNELLS More Detail

    AR-15/M16 USGI MAGPUL FOLLOWER + SS SPRING KITS BROWNELLS

    $3.99 - $9.99$3.99 - $9.99

    This M16 USGI Magpul Follower and Spring Kit breathes new life into used or unreliable magazines.  Kit available as singles or in a three pack. The Magpul Enhanced Self-Leveling Follower is a drop in replacement for the aluminum USGI 30-round magazine black or green follower.Featuring a patent pending 4-way anti-tilt design for increased feeding reliability, the Enhanced Self-Leveling Follower is made from a non-hygroscopic and self-lubricating polymer. The Brownells SS Spring follows government specifications, and is the same spring included in our previous runs of Government contract magazines.    

    HOT!
  • AR-15/M16 USGI RANGER® FLOORPLATE 3 PACK MAGPUL More Detail

    AR-15/M16 USGI RANGER® FLOORPLATE 3 PACK MAGPUL

    $18.95$18.95

    Easier Mag Changes With Just A FingerTwo-piece, slide-on replacement for factory floorplate has a smoothly contoured, easy-to-grasp finger loop that helps you perform lightning-fast magazine changes in high stress situations. Aids in fast, positive extraction from tight mag pouches and helps you hang onto the empty magazine with just a finger after a tactical reload. Also cushions magazine from impact when dropped concrete or other hard surfaces. Made from tough, yet soft, non-slip synthetic rubber over a stainless steel core that snaps into a reinforced polymer insert to keep the Rangerplate firmly locked to the magazine. Includes molded-in para-cord hole for custom loop configurations. Sold in 3-paks and available in Black, Dark Earth and O.D. Green. AR-15, Issue:11, Page:064 Big Book Catalog, Issue:69, Page:064 Sinclair, Issue:5B, Page:246

    HOT!
  • TARAN TACTICAL INNOVATIONS AR-15 CUSTOM 5.56 PMAG EXTENSION 3-PKS BROWNELLS More Detail

    TARAN TACTICAL INNOVATIONS AR-15 CUSTOM 5.56 PMAG EXTENSION 3-PKS BROWNELLS

    $99.99$99.99

    These PMAG magazine extensions have been customized with the Brownells logo and easily attach to increase the capacity of 5.56 PMAGS. The 5.56 extension adds 5 rounds to 30 round PMAGS and 6 rounds to 40 round magazines. Machined from a single piece of aluminum, extensions utilize the factory magazine spring and require no special tools for installation. Extension’s extra weight also ensures the magazine drops free of the rifle for quicker reloads during competition shooting or tactical situations. Sold in packs of 3.

    HOT!
  • AR-15/M16 USGI 30RD MAGAZINE REBUILD KIT BROWNELLS More Detail

    AR-15/M16 USGI 30RD MAGAZINE REBUILD KIT BROWNELLS

    $3.99 - $17.99$3.99 - $17.99

    Replacement spring, follower, and floorplate install easily to eliminate problems caused by worn-out parts. Chrome silicon spring maintains proper tension and gives consistent feeding, also available with stainless steel spring. 30-round followers are made of fiberglass-filled plastic. Anodized aluminum floorplate. Available for mil-spec 30-round magazines. AR-15, Issue:11, Page:062 Big Book Catalog, Issue:69, Page:063

    HOT!
  • AR-15/M16 USGI MAGPUL FOLLOWER + CS SPRING KITS BROWNELLS More Detail

    AR-15/M16 USGI MAGPUL FOLLOWER + CS SPRING KITS BROWNELLS

    $3.99 - $9.99$3.99 - $9.99

    This M16 USGI Magpul Follower and Spring Kit breathes new life into used or unreliable magazines.  Kit available as singles or in a three pack. The Magpul Enhanced Self-Leveling Follower is a drop in replacement for the aluminum USGI 30-round magazine black or green follower.Featuring a patent pending 4-way anti-tilt design for increased feeding reliability, the Enhanced Self-Leveling Follower is made from a non-hygroscopic and self-lubricating polymer. The Brownells CS Spring follows government specifications for spring tension and diameter, but with the added benefit of corrosion and set resistance.  

    HOT!
  • AR-15/M16 SINGLE SHOT MAGAZINE FOLLOWER SINCLAIR INTERNATIONAL More Detail

    AR-15/M16 SINGLE SHOT MAGAZINE FOLLOWER SINCLAIR INTERNATIONAL

    $17.99$17.99

    If you are using the longer, heavier bullets in your AR-15, then you need a Sinclair AR-15 Single Shot Follower. The longer, heavier bullets are normally loaded longer than magazine length. The Sinclair AR-15 Single Shot Follower positions the 223 Remington cartridge loaded with longer bullets correctly for smooth feeding into the chamber. Once a round is fired, the bolt retracts and locks behind the follower in the empty/loading position. No need to take your magazine apart! It takes only a few seconds to install the Sinclair Follower on top of the existing follower. It can be removed just as quickly. This follower addresses many of the problems with existing single shot followers on the market. The satin finished anodized aluminum wears better than the plastic followers and is easily noticeable in the magazine. Works perfectly in GI metal magazines and Brownell magazines. Will not work in any of the inexpensive, plastic magazines we tested. Will work with 450, 450 Bushmaster. AR-15, Issue:11, Page:063 Big Book Catalog, Issue:69, Page:062 Sinclair, Issue:5B, Page:247

    HOT!
  • AR-15/M16 30RD MAGAZINE BODY BROWNELLS More Detail

    AR-15/M16 30RD MAGAZINE BODY BROWNELLS

    $8.99$8.99

    High capacity Magazine Bodies available in 30-Round. AR-15, Issue:11, Page:062 Big Book Catalog, Issue:69, Page:063

    HOT!
  • AR15 CUSTOM 5.56 PMAG EXTENSION BROWNELLS More Detail

    AR15 CUSTOM 5.56 PMAG EXTENSION BROWNELLS

    $39.99$39.99

    These PMAG magazine extensions have been customized with the Brownells logo and easily attach to increase the capacity of 5.56 PMAGS. The 5.56 extension adds 5 rounds to 30 round PMAGS and 6 rounds to 40 round magazines. Machined from a single piece of aluminum, extensions utilize the factory magazine spring and require no special tools for installation. Extension’s extra weight also ensures the magazine drops free of the rifle for quicker reloads during competition shooting or tactical situations.

    HOT!
  • AR-15 ORIGINAL MAGPUL 5.56 MAGPUL More Detail

    AR-15 ORIGINAL MAGPUL 5.56 MAGPUL

    $9.45$9.45

    Fast, Fumble-Free Mag Changes Thermoplastic loop installed on the base of a rifle or subgun magazine to provide an easy-to-grasp handle for unsurpassed speed and controllability during high stress, tactical magazine changes. Recessed, rough texture provides positive gripping surface under slippery or wet conditions. Finger loop acts as shock absorber to protect magazine from damage when dropped from rifle. Silences magazines stored next to each other in pouch. AR-15, Issue:11, Page:064 Big Book Catalog, Issue:69, Page:064 Big Book Catalog, Issue:69, Page:174

    HOT!
  • AR-15/M16 USGI L-PLATE MAGPUL More Detail

    AR-15/M16 USGI L-PLATE MAGPUL

    $18.95$18.95

    Protects USGI Mags From Impact On Hard Surfaces & Aids Extraction From Mag Pouches The L-Plate is a replacement floor plate for current-issue USGI 30-round magazines that gives your AR mag a soft, rubber bumper pad that cushions it from damage when ejected on the hard ground. Low-profile – adds only ½" to mag when installed – yet also provides a secure grasping point for pulling mags quickly from mag pouches. Stainless steel core is overmolded with tough, durable Santoprene rubber, so the L-Plate handles all the tactical and competition abuse you can dish out. Holes through the L-Plate let you add paracord pull loops. Perfect enhancement for Brownells 20- and 30-round AR-15/M16 magazines. AR-15, Issue:11, Page:063 Big Book Catalog, Issue:69, Page:063

    HOT!
  • AR 308 CUSTOM 7.62 PMAG EXTENSION BROWNELLS More Detail

    AR 308 CUSTOM 7.62 PMAG EXTENSION BROWNELLS

    $44.99$44.99

    These PMAG magazine extensions have been customized with the Brownells logo and easily attach to increase the capacity of 7.62 PMAGS. This 7.62 version will extend your PMAG20 LR/SR and PMAG25 LR/SR by 6 rounds. CNC machined from billet aluminum and finished with a hard coat anodize, these utilize the factory magazine spring and easily attach without specialty tools.

    HOT!
  • M14/M1A MAGAZINE SPRING WOLFF More Detail

    M14/M1A MAGAZINE SPRING WOLFF

    $22.99 - $55.99$22.99 - $55.99

    Extra Power Improves RelialilityReplace those old, tired, GI springs to improve function. 5% extra power assures reliable feeding in all conditions. Drop-in replacement fits 20-round magazine. Big Book Catalog, Issue:69, Page:178

    HOT!
  • AR-15/M16 20RD MAGAZINE BODY BROWNELLS More Detail

    AR-15/M16 20RD MAGAZINE BODY BROWNELLS

    $8.99$8.99

    Bring Magazines Back To Top Performance High capacity Magazine Bodies available in 20-Round. AR-15, Issue:11, Page:062 Big Book Catalog, Issue:69, Page:063

    HOT!
  • AR-15/M16 PMAG M3 FIREPOWER EXTENSION TARAN TACTICAL INNOVATIONS More Detail

    AR-15/M16 PMAG M3 FIREPOWER EXTENSION TARAN TACTICAL INNOVATIONS

    $39.99$39.99

    Expands PMAG Capacity By Up To 6 Extra Rounds Drop in magazine extension allows you to increase the capacity of both 5.56 and 7.62 PMAGS. The 5.56 extension adds 5 rounds to 30 round PMAGS and 6 rounds to 40 round magazines. Extensions for 7.62 PMAGS add 6 rounds to both the 20 and 25 round magazines. Machined from a single piece of aluminum, extensions utilize the factory magazine spring and require no special tools for installation. Extension’s extra weight also ensures the magazine drops free of the rifle for quicker reloads during competition shooting or tactical situations.

    HOT!
  • AR-15/M16 PMAG M3 7.62 MAGAZINE-5RD LIMITER MAGPUL More Detail

    AR-15/M16 PMAG M3 7.62 MAGAZINE-5RD LIMITER MAGPUL

    $13.25$13.25

    Drop-In Insert Temporarily Reduces Mag Capacity Hard polymer insert snaps into the floorplate to limit capacity for sporting or hunting applications. Installs easily without tools and requires no permanent alteration of the magazine. Will not make a banned magazine legal, as capacity reduction is not permanent. Minus 5 reduces capacity by 5 rounds. AR-15, Issue:11, Page:061 Big Book Catalog, Issue:69, Page:061

    HOT!
  • 308 AR PMAG FIREPOWER EXTENSION TARAN TACTICAL INNOVATIONS More Detail

    308 AR PMAG FIREPOWER EXTENSION TARAN TACTICAL INNOVATIONS

    $44.99$44.99

    Get the most out of your PMAGs with the Firepower Extensions from Taran Tactical Innovations. With models available for 7.62 PMAGs, the 7.62 version will extend your PMAG20 LR/SR and PMAG25 LR/SR by 6 rounds. CNC machined from billet aluminum and finished with a hard coat anodize, these utilize the factory magazine spring and easily attach without specialty tools.

    HOT!
  • AR-15/M16 USGI 20RD CS MAGAZINE REBUILD KIT BROWNELLS More Detail

    AR-15/M16 USGI 20RD CS MAGAZINE REBUILD KIT BROWNELLS

    $3.99 - $17.99$3.99 - $17.99

    Bring Magazines Back To Top Performance Replacement spring, follower, and floorplate install easily to eliminate problems caused by worn-out parts. Chrome silicon spring maintains proper tension and gives consistent feeding, also available with stainless steel spring. 20-round followers are made of fiberglass-filled plastic. Anodized aluminum floorplate. Available for straight body 20-round magazines. AR-15, Issue:11, Page:062 Big Book Catalog, Issue:69, Page:063

    HOT!

Subscribe our newsletter

Lorem ipsum dolor sit amet, consectetur adipisicing elit. Ex, velit!