• BARREL LINER DRILLS BROWNELLS More Detail

    BARREL LINER DRILLS BROWNELLS

    $81.99 - $108.99$81.99 - $108.99

    Special Deep-Hole Drill For Installing Barrel LinersFor the gunsmith who does not want to make his own drill extension, our Hi-Speed steel drills are designed especially for deep hole drilling for Brownell Barrel Liners. The hole for the liner must be drilled slightly more than halfway from each end, and the ONLY way to ensure proper joining when using a hand drill is to use these piloted drills. Special, helix angle eliminates the tendency for the drill to pull itself into the material and jam, saving time and headaches. The extra cost for this premium quality drill is far cheaper than ruining a customers gun with an off-center hole. Given proper care, will last a lifetime. Big Book Catalog, Issue:69, Page:167 Big Book Catalog, Issue:69, Page:449

    HOT!
  • SOLID CARBIDE DRILL BROWNELLS More Detail

    SOLID CARBIDE DRILL BROWNELLS

    $19.99 - $29.99$19.99 - $29.99

    For Hard ReceiversSpecially ground, single-flute, solid carbide drills ideally suited for use by the professional gun trade on hard receivers (as the 03A3 and harder). • Cuts a clean chip in hardest file steel, giving true hole. • Does not "crumble out" the steel; thus, no chatter. • 2" long to give quill clearance when using with Forster and other scope/sight mounting jigs. • Kept properly cleaned, will not bind or break. • Properly fed, won't work-harden hole surface like spade drill does; decreases tap breakage. • Drills "all the way through" hardened steels. Note: Common sense must be used. No guarantee against breakage! Use only to crack the skin on Krags and the like. DO NOT USE IN SOFTER STEELS. Use only after other drills have failed or hardness of steel is preknown. Big Book Catalog, Issue:69, Page:450

    HOT!
  • WIRE GAUGE DRILLS - JOBBER LENGTH TRIUMPH TWIST DRILL CO. More Detail

    WIRE GAUGE DRILLS - JOBBER LENGTH TRIUMPH TWIST DRILL CO.

    $2.99 - $5.99$2.99 - $5.99

    U.S. MadeA heavy-duty drill can make all the difference in the world in your work. The extra engineering and care in manufacture will help you to drill cleaner, more accurate holes, and many more of them at that. All the Drills we carry, Sets, Individuals, Jobber Length and Short Length, are made from High Speed Steel with a 135 self-centering point. Special point and surface treatments (Maxi-Set not treated) give easier, more wear-resistant drilling of the tough steels encountered in the gun shop. Big Book Catalog, Issue:69, Page:450

    HOT!
  • 3-FLUTE CARBIDE DRILL BROWNELLS More Detail

    3-FLUTE CARBIDE DRILL BROWNELLS

    $19.99 - $22.99$19.99 - $22.99

    Drill More, More-Accurate Holes, Faster Three-flute design spreads cutting loads over a larger area so holes are cleaner and rounder. The bit itself will last longer too. Designed for cutting hard metals: stainless, nickel steel alloys, titanium plus, great on soft metals too. Big Book Catalog, Issue:69, Page:450

    HOT!
  • JOBBER LENGTH MAXI SET TRIUMPH TWIST DRILL CO. More Detail

    JOBBER LENGTH MAXI SET TRIUMPH TWIST DRILL CO.

    $545.99$545.99

    This Is It-Never Want For The Right Size Again Big Book Catalog, Issue:69, Page:450

    HOT!
  • SHORT, PILOTED BARREL LINER DRILL n/a More Detail

    SHORT, PILOTED BARREL LINER DRILL n/a

    $52.00 - $88.75$52.00 - $88.75

    Save Money By Adding Your Own ExtensionIf you can silver solder or braze your own extension onto a Liner Drill, these standard length, deep hole drills can save you money. Piloted to follow the original bore and have all the same high-grade features as our .22 Liner Drill: Deep hole flute geometry and special helix angle to prevent jamming; reinforced web for accurate hole dimensions; nitrided lands for long life. Big Book Catalog, Issue:69, Page:167 Big Book Catalog, Issue:69, Page:168 Big Book Catalog, Issue:69, Page:450

    HOT!
  • CARBIDE CENTER DRILL BROWNELLS More Detail

    CARBIDE CENTER DRILL BROWNELLS

    $24.99 - $53.99$24.99 - $53.99

    For Frozen Screw Removal And Long, Long LifeIf none of the common methods for removing a frozen screw work, and drilling is in order, these carbide center drills should be used to center and "start" the hole. With the spindle at fairly high speed, bring the center drill down to the screw head and adjust position until centered in the screw. Apply pressure and cut until center hole is deep enough to allow the proper undersized, regular drill bit to start cutting without catching on the screw head slot. Better for drilling broken taps too, for they will cut center holes in even the hardest ones. And, because of the large body mass of the tool relative to the small drill diameter, it is very sturdy and rigid. Will not flex or walk. Big Book Catalog, Issue:69, Page:450

    HOT!
  • WIRE GAUGE DRILLS - SHORT LENGTH TRIUMPH TWIST DRILL CO. More Detail

    WIRE GAUGE DRILLS - SHORT LENGTH TRIUMPH TWIST DRILL CO.

    $1.50 - $4.99$1.50 - $4.99

    U.S. MadeA heavy-duty drill can make all the difference in the world in your work. The extra engineering and care in manufacture will help you to drill cleaner, more accurate holes, and many more of them at that. All the Drills we carry, Sets, Individuals, Jobber Length and Short Length, are made from High Speed Steel with a 135° self-centering point. Special point and surface treatments (Maxi-Set not treated) give easier, more wear-resistant drilling of the tough steels encountered in the gun shop. Big Book Catalog, Issue:69, Page:450

    HOT!
  • 1911 GRIP BUSHING STAKER BROWNELLS More Detail

    1911 GRIP BUSHING STAKER BROWNELLS

    $3.99 - $31.99$3.99 - $31.99

    8-Segment, 90\ Head Gives Maximum Contact To Frame For Most Secure Bushing Installation Possible 1911 stock bushings get bunged up or lost in the field or when a pro is doing a "Master Reblue Job" they get removed to permit the finest possible polishing job. Then they have to be replaced and that can be a real chore. No more. With this special Brownells 1911 Auto Grip Bushing Staker, it's now quick and easy to get them tight on the first try. Made in 8 segments with 90° cuts between for maximum bushing contact to frame. Has "handle" and deep hole in top of Staker to prevent your 1/8" punch from slipping off. (The 1/8" punch passes thru bushing center on opposite side of frame to give clean access to bushing being replaced or tightened.) Note: Make an anvil block to support outside of bushing while it is being staked. Works great! 1911, Issue:11, Page:053 1911, Issue:11, Page:055 Big Book Catalog, Issue:69, Page:143 Big Book Catalog, Issue:69, Page:145

    HOT!
  • FRACTIONAL DRILLS - JOBBER LENGTH TRIUMPH TWIST DRILL CO. More Detail

    FRACTIONAL DRILLS - JOBBER LENGTH TRIUMPH TWIST DRILL CO.

    $1.99 - $31.99$1.99 - $31.99

    U.S. MadeA heavy-duty drill can make all the difference in the world in your work. The extra engineering and care in manufacture will help you to drill cleaner, more accurate holes, and many more of them at that. All the Drills we carry, Sets, Individuals, Jobber Length and Short Length, are made from High Speed Steel with a 135 self-centering point. Special point and surface treatments (Maxi-Set not treated) give easier, more wear-resistant drilling of the tough steels encountered in the gun shop. 1911, Issue:11, Page:055 1911, Issue:11, Page:059 Big Book Catalog, Issue:69, Page:145 Big Book Catalog, Issue:69, Page:146 Big Book Catalog, Issue:69, Page:450

    HOT!
  • TiN COATED DRILL n/a More Detail

    TiN COATED DRILL n/a

    $4.99 - $10.99$4.99 - $10.99

    Stays Sharper Longer For Accurate Drilling Big Book Catalog, Issue:69, Page:450

    HOT!
  • LETTER DRILLS - JOBBER LENGTH TRIUMPH TWIST DRILL CO. More Detail

    LETTER DRILLS - JOBBER LENGTH TRIUMPH TWIST DRILL CO.

    $4.99 - $15.99$4.99 - $15.99

    U.S. MadeA heavy-duty drill can make all the difference in the world in your work. The extra engineering and care in manufacture will help you to drill cleaner, more accurate holes, and many more of them at that. All the Drills we carry, Sets, Individuals, Jobber Length and Short Length, are made from High Speed Steel with a 135 self-centering point. Special point and surface treatments (Maxi-Set not treated) give easier, more wear-resistant drilling of the tough steels encountered in the gun shop. Big Book Catalog, Issue:69, Page:450

    HOT!

Subscribe our newsletter

Lorem ipsum dolor sit amet, consectetur adipisicing elit. Ex, velit!